Trojan TWC-35 35-Inch Tall Work Center, 2 by 6 Not Included

Cheap Trojan TWC-35 35-Inch Tall Work Center, 2 by 6 Not Included Review

In preparation for building my house, I bought the work center of Troy 35 "(TWC-35) for a price of 115.00 to fly, take my Milwaukee 12" sliding compound miter saw (seen enough heavy) . Also bought an extra roll.

Many people have to consider the 27 "or 35" kit. I did a lot to think about how high I wanted the saw before buying the larger size. I used a 2x6 14 'that passes through to the last 10 months. I'm 5'8 "with a 30" inseam, and I did not oncethought about the height of the saw with this configuration - it was perfect. The material is there, safely in front of you without bending over. My 5'7 "with 28" inseam 76 years old father has put a lot of time on this saw / stand and prefers the 35 "too high. At this stage, I could not imagine using the center 27 Work," by back is tired enough as it is. I ran almost all the material through the saw, including all sizes of wood, OSB, PVC, Hardiplank, fittings, etc., and never had a negative impactthought about the final height of the saw with 35 "legs and 2x6 crossbar. I do not have 27" legs too, and it is unnecessary to use the saw stand - 35 "is the way forward.

"I use a single clamp 24" mounted vertically as a cessation of multiple cuts of the same length, very adjustable in this way.
The saw stand-hook mounting base a little loose on the size of 2x6 wood, so I propped the clamps tightened with two old 7-1/4 "blade one-framer carbide, and exploitnext to the timber so that the clips that tighten against the metal of the blade. Takes a lot of stir because the clamps normally just dig into the tie and never really close. Any thin metal working to make this dock.
-If your saw is heavy, as is mine, there will be some flex in the Assembly as a saw head slides on the track and the scales tip toward you. This is a very slight flexion and does not bother me.
The guide-roller that I bought is more convenientkeep a roll on one side and two on the other side. Much less mobile shingle around.
-Two people can move the stand / saw combo fairly easily. Sliding he set his legs as they enter the sub-floor, particularly with a heavy saw. Does not seem to cause permanent damage, but probably not good to move around. Would cutting blade on the concrete well.
-If no help is available and the stand must be moved several ways, I just remove the base of the saw and the operations change.
Legs-clampingwood as a person. Get placed at the correct angle, use your feet to start the legs apart to tighten the wood, then lightly step on the support via their snap in the lockset. Then do the same thing for another. Takes a little practice, but in the end I can get them quickly and safely. The teeth dig and there is no way those legs off, unless you want them. I read about someone complaining about his legs in bulk: the standard dimensionalWood is simply not possible. I think perhaps he does not step in the cons-ways to tighten hinge and lock. They are foolproof, if properly installed.
During the phase of siding construction, the work center stayed out of cold showers and occasional. I was initally concerned about the humidity ruining the base, but it has. We bungeed a tarp on the saw and a work center and everything was fine. The moisture would eventually cause a problem if, if left exposed. If you're breakingthis every night and throw the pieces in a truck - the base of the saw must be protected from moisture during travel. Of course, it would be fairly simple to make a new base and mount the bracket on it.
-To measure up, I'm almost using the worst case with the Milwaukee 12 "SCMS. It is a beast and runs very well on this stand, just a little flex as shown.
-On occasion, I used a separate 35 "rack * Trojan I c-clamed the 2x6 work center to providesupport additional work long. By C-clamp center woodworking wood saw horse, I was able to mount the pipe clamp has been previously discussed in the section of bridge to make several cuts long as possible. I also have a booth on wheels out to the early support of long duration.
-Experience the duration and location of the 2x6 wooden leg to get the best performance, reduce some flex and give more space to move through the rollers. Watch the balance. The machine must not necessarily becentered on the 2x6 and can be positioned in the center. The instructions tell you this Trojan is that you do, but common sense allows variance. With a 2x6 long enough and some thought that we have implemented support for managing both left and right feed roller without moving much. You'll need some elbow room on site to do so.

* I have enough extra legs of Troy for the construction of two 35 "saw horses with 2x6 timber and two 27" 2x8 wooden trestles. You can use different wood fordifferent heights - at your fingertips. Each level had its own uses and I am more than satisfied with the performance. Simple, very strong and very reliable. These things take a stack of weight and have not met their match at the moment - and doubt they will.

Full line of Trojan workcenters easel legs / are strong, versatile, highly mobile, and The Cat's Meow far as I'm concerned. Excellent buy, expecially if you catch the work center for sale 115-120. I never noticedeasel legs pass to a sale price, but the center 35 of work "certainly did.

Trojan TWC-35 35-Inch Tall Work Center, 2 by 6 Not Included Feature

• Fast setup and stores conveniently
• Use with mitre saws, planers, tablesaws, drill presses
• Use any 2x lumber for the size you want
• Gripping teeth clamp wood without screws or nails

Trojan TWC-35 35-Inch Tall Work Center, 2 by 6 Not Included Overview

The Trojan Work Center is so easy to set up, in just seconds you've got a work station that keeps you and your work off the ground. Ball bearing rollers adjust to the proper height and make material feed easily. The rollers stow conveniently with the table to make a briefcase size unit to carry between jobs. The work center is suitable for use with miter saws, planers, table saws, drill presses, radial saws, extra horses, etc. Trojan TWC35 35" Tall Work Center. Includes: Sawhorse legs, 2 roller brackets, saw table, Additional rollers available (model TR-10). Saw NOT Included.



*** Product Information and Prices Stored: Apr 27, 2010 17:56:32