JDS Company 24-46 24-Inch - 46-Inch Accu-Miter Table Saw Miter Gauge

Cheap JDS Company 24-46 24-Inch - 46-Inch Accu-Miter Table Saw Miter Gauge Review

First let me tell you that you will not only get better indicator tab for the money to buy it from Amazon. As I write this, the MRSP for this gauge is $ 239. Amazon sells it for $ 101! Read that twice - yep - $ 101. Which is far below the selling price of the manufacturer of the Amazon, which is selling at a loss. I thought it was a good deal on the $ 162 I paid (price at the time on Amazon).

Secondly, the ratings on this gauge have suffered somewhat of a bad originalProduct picture, which shows the clip option. Some of those who do not read what is included and what was not down-rated the product when they did not check. While I understand why it has stuck and it may be, indeed, easy to forget something like that, it should not affect the rating of the product itself.

In my opinion ...

Things I like: The construction is heavy and solid. The stock aluminum bar is large and straight. The miter bar slot nylonsetting work perfectly, but note that you want to adjust when the bar is not in the apartment. They are easy to adjust when the bar is out of the slot, and almost impossible when it is in the slot. The adjustable stop is the best I've seen on a miter gauge.

I thought that things could be better: the scale is fixed, making it useless, except for a rough estimate at the position 90 degrees. The scale on the telescoping section is actually upside down from the ladder on the mainextrusion! It actually makes sense if you use it, but is certainly a little bizarre. Two handles to set the bar at the top is a little pain and handles in your way sometimes.

Other comments:

The basic accuracy of the tool is fixed in mounting the device firing pin itself. If you do not set that up right, the gauge will never be exact. The horse is fussy and uses several small screws. It is possible to rob or threaded holes in which theyscrew. My advice is to carefully screw them in without the adapter plate or pin mechanism first time, back them, then attach. I did it after feeling a slight resistance in a screw and had no problem. This is a configuration problem once.

The precision of the firing pin mechanism itself, you still have to lock the head after setting the correct angle when you use the PIN shot. JDS will tell you that most complaints about the accuracy consume is because users are not lockedgauge, thinking of firing pin will hold the corner! The mechanism of Pine plan is accurate, but you must learn to use it. I found that it provides accurate, repeatable results and while it is used in the same way every time. Firstly, it must engage the pin with a snap. If you try to finesse or force, you're essentially going to just hang at an angle slightly closed. Allow the candle - which is machined to a high degree of accuracy - to do its job. The pin and holefaces are also a few (small) lubrication. Finally, smooth the use of the mechanism even more. These remarks apply to any mechanism pin shot.

I give the gauge a 4 instead of 5 for one main reason: as good as the gauge is, you can bend the head extensions longer. You can reduce or eliminate that, making sure the inventory control and gauge closest to the head (ie, not allowing the weight of the stock on the outer end to deflect the pressure gauge), but I have been hoping that it wouldbe more severe. This is not a substitute for a saw sled lengths longer, at least not for the heavy equipment and panels.

JDS Company 24-46 24-Inch - 46-Inch Accu-Miter Table Saw Miter Gauge Feature

• Shot-pin accuracy for 90-, 45-, 30-, 22-1/2-, and 15-degree angles
• Precise protractor scale for less frequently used angles
• Rigid, front fence with telescopic extension
• Adjustable end stops for repetitive cross cuts
• Outer rail end stop 24-1/2 inches on this model

JDS Company 24-46 24-Inch - 46-Inch Accu-Miter Table Saw Miter Gauge Overview

Get Accurate Miters And Crosscuts With Any Tablesaw Or Shaper



*** Product Information and Prices Stored: Mar 25, 2010 02:29:53